✦Basic product information：

Fanuc’s IC698RMX016 is a 16MB redundant memory Xchange for the Rx7I Pacsystem. It has the following dimensions: 6.299 inches wide x 9.187 inches high. It has 16MB of SDRAM user memory. The power supply operates at +5 V DC. The current requirement is 1.8A. The device has optical fiber LC connectors and zirconium ceramic ferrule according to IEC 61754-20. The maximum insertion loss is 0.35 dB and return loss is -30dB. The acceptable temperature range is -20°C to +85°C. To complete the installation, you need to ensure that you have all of the following: a PACSystems RX7i CPU with firmware version 2.00 or higher; A PACSystems Rx7i CPU rack with power supply; A PC-compatible computer with CIMPLICITY Machine Edition – Logic Developer PLC, programming software version 4.5 or later, and the necessary cables.

Note that in order to meet radiation emission standards, RX7i systems containing multiple Memory Xchange modules must be installed in a pipe metal housing or equivalent housing. Memory modules can only be installed in RX7i rack 0 (main). It is recommended that the RMX module be installed in slots 4 and 3 of the chassis. This gives the RMX module a VME interrupt request priority. While such a configuration is recommended, it is not strictly required that RMX modules

IC698RMX016-ED

be placed in slots 4 and 3. To install the redundant memory swap IC698RMX016, ensure that the rack is powered off. Next, slide the module into the exact slot configured for it in the system. Continue to press the board into place without forcing it. Tighten the top and bottom screws of the panel. Next, make sure to connect the cables to the RX and TX connectors. The fiber optic cable should be routed from the TX connector to the RX connector of the next node. Connect the board’s TX cable to the RX connector on the next node. Repeat the above steps until the TX of the last node in the ring is routed to the RX connector of the first node. Turn on the power.

The IC698RMX016 is initially powered on in an unconfigured state where its light emitter is disabled. The redundant memory Xchange module will not be able to run on the network until the RX7i CPU sends the hardware configuration to the module. To perform reflective memory operations, the user can choose to configure the following parameters: redundant transport mode, node ID, network memory offset, Rogue Master, and Interrupt enable. Note that if redundant link operation is selected, the above parameters are set by the CPU and therefore cannot be configured. Note that if the IC698RMX016 is used as a reflective memory module with a general purpose, it expands to additional functions beyond basic read and write operations, including reading interrupt states, enabling interrupts, reading parity errors, and enabling parity.

IC698RMX016-ED

✦About Chengdu Sunshine Xi He

Chengdu Sunshine Xi He Electric Co., Ltd. specializes in selling the world’s major electrical brand products overseas direct procurement,

genuine inventory, price preferential after-sales warranty, complete models, the same product, not the same price and service.

Large supply of original imported DCS system accessories, PLC system accessories.

Main :ABB, GE Fanuco, Bentl Bentley, Triconex Invensys, Woodward Woodward, Foxboro, Foxboro,

Westinghouse /Emerson, Reliance Ryan, SchneiderModicon, A-B, HIMA dark horse, Motorola MOTOROLA,

Kollmorgen Kollmorgen Bosch/Rexroth/ Bosch Rixon, NI,YOKOGAWA Yokogawa, and other major brands of DCS system accessories,

robot system accessories, large servo system discontinued spare parts.

✦Contact us freely

BeiLin

| Mobile/wechat：+86 18005021035

Email contact：18005021035@163.com

✦What can we do for you?

1. All items are new.
2. Any enquiry will be answered within 1 hour.
3. We check them before shipping!

✦About Frequently Asked Questions

Q: Are you a trading company or a manufacturer?
A: Yes, we are a trading company.

Q: Do you have stock or need to buy from another supplier?
A: We have a lot of inventory to sell and we have our own warehouse.

Q: Do you sell outdated products? Or even a very old product?
A: If there is a new model that needs to be replaced, we will recommend that you use the new model;
If the replacement is not easy, we will help check that the old car is in good condition.
If used or otherwise, we will tell you the truth.

Q: How long is your delivery time?
A: If the goods are in stock, it usually takes 2-3 working days. If the quantity is large,
It takes 5-7 business days after receipt of payment.
If it is not an ordinary product, it always takes 3-4 weeks to order.

✦You may be interested